I am using the SX1262 for receiving packets with EXPLICIT_HEADER_MODE enabled (the header is present). I have the latest libraries from Semtech (link). The problem is that when I receive data, the sx126x_get_rx_buffer_status function is called to determine the size of the received packet. However, this function returns incorrect information about the payload length. Although when I read the data buffer, the data is received correctly.
SX126x Get RX payload size
129 Views Asked by WITC At
0
There are 0 best solutions below
Related Questions in STM32
- Build issue in my STM32-NUCLEO project using the Eclipse IDE
- STM32 ADC DMA low raw/Voltage readings
- Program doesn't run after DFU
- STM32G030 refuses write to flash
- STM32 - Serial Audio Interface (SAI) - dual data line transmit possible?
- CLion: Debug via St-Link
- STM32 RTC3 Mixed Mode: Writing TR resets SSR
- Ran on an MCU (STM32F1), doubly-linked list code results in a call of HardFault() due to stack overflow
- i want to display voltage of ADC with " ssd1306 OLED " in STM32 when i change the voltage with potentiometer
- spi5 of my STM32MP157F-K2 CAN'T read data from the RC522 CARD
- STM32 unable to be read
- Enabling one timer using another
- Confusion with thumb instructions while compiling recipe for cortexm4 CPU
- How to setup Interface Encoder mode for the STM32F0
- UART Driver for STM32MP25 by EDK2
Related Questions in LORA
- Sending Struct Package over LoRa - When Sensor Value Changes, Transmit Stops
- LoRa communication between two boards
- Why isn't my LoRa module working with Arduino?
- Waveshare SX1262 LoRaWAN Hat
- Deployment Issue with ChirpStack and Helium: GRPC Permission Denied Error
- Is there a way to establish a LoRa connection between a SX1262 868M LoRa Hat and an ESP32 WiFi LoRa V3 from Heltec?
- SX126x Get RX payload size
- How to fix error 'AttributeError: module 'board' has no attribute 'D5'
- LoRa ESP32 V2 board ("Core 1 panic'ed")
- How can I combine 2 modules in STM32?
- Unable to get LoRa P2P up with ATSAMR34
- Code works on Arduino IDE but not PlatformIO
- SAMR34 basic example fails with, unknown field 'pfnNMI_Handler', 'pfnSVC_Handler'
- Failed to add edge detection - Raspberry Pi 4 GPIO
- I want to send data to Azure IoT hub through Chirpstack
Related Questions in LORAWAN
- SSL/TLS error occurs when sending http request to Helium LoraWAN Server with restsharp (106.6.1) or httpwebrequest in .net 4.8
- Custom Join request on LoRaWAN End Node STM32L0
- LoRaWan with LMIC only sporadically receiving messages
- Waveshare SX1262 LoRaWAN Hat
- Deployment Issue with ChirpStack and Helium: GRPC Permission Denied Error
- SX126x Get RX payload size
- How can I capture packets on devices with OneShotSenderHelper (signetlabdei / LoRaWAN module) application installed in ns3?
- What is the tenant ID for The Thing Network au1 region?
- LoRa ESP32 V2 board ("Core 1 panic'ed")
- The Things Stack | LoRaWAN AppEUI
- I want to send data to Azure IoT hub through Chirpstack
- Decode payload sent from TN via Cocoa MQTT library
- About AppEUI for I-NUCLEO-LRWAN1
- Problem receiving join requests and connection status from LoraWAN gateway inside AWS IOT Core LPWAN
- Blackpill not sending data after some frame counts (nearly 200-400) through RFM96
Related Questions in MODULATION
- 4-FSK GnuRadio demodulation
- Why do I find a low frequency oscillation when I add a carrier frequency to my baseband signal ? And Why is my demodulation step not working?
- Error with "make" when installing gr-tutorial-master for analyze QSPK
- Sounddevice Output Overflow
- I 'am working on a problem of modulation and demodulation using CPFSK. but the Demodulated output stream is not correct even without adding any noise?
- SX126x Get RX payload size
- ASK Modulated Signal Envelope (Python)
- WebSDR and continuous wave (CW) demodulation of DCF77 signal
- SVPWM Dwell time calculation and switching vector
- ESP32 - ESP-IDF - Sweep frequency DAC
- How to get BER for QPSK modulation?
- Extract frequency of sin wav from clean and noisy numpy arrays
- BER result in MATLAB
- FSK modulation matlab code is not working as expected
- phase modulation in LabVIEW
Trending Questions
- UIImageView Frame Doesn't Reflect Constraints
- Is it possible to use adb commands to click on a view by finding its ID?
- How to create a new web character symbol recognizable by html/javascript?
- Why isn't my CSS3 animation smooth in Google Chrome (but very smooth on other browsers)?
- Heap Gives Page Fault
- Connect ffmpeg to Visual Studio 2008
- Both Object- and ValueAnimator jumps when Duration is set above API LvL 24
- How to avoid default initialization of objects in std::vector?
- second argument of the command line arguments in a format other than char** argv or char* argv[]
- How to improve efficiency of algorithm which generates next lexicographic permutation?
- Navigating to the another actvity app getting crash in android
- How to read the particular message format in android and store in sqlite database?
- Resetting inventory status after order is cancelled
- Efficiently compute powers of X in SSE/AVX
- Insert into an external database using ajax and php : POST 500 (Internal Server Error)
Popular # Hahtags
Popular Questions
- How do I undo the most recent local commits in Git?
- How can I remove a specific item from an array in JavaScript?
- How do I delete a Git branch locally and remotely?
- Find all files containing a specific text (string) on Linux?
- How do I revert a Git repository to a previous commit?
- How do I create an HTML button that acts like a link?
- How do I check out a remote Git branch?
- How do I force "git pull" to overwrite local files?
- How do I list all files of a directory?
- How to check whether a string contains a substring in JavaScript?
- How do I redirect to another webpage?
- How can I iterate over rows in a Pandas DataFrame?
- How do I convert a String to an int in Java?
- Does Python have a string 'contains' substring method?
- How do I check if a string contains a specific word?